Remington® 700 (tool rentals)
Showing all 16 results
-
Heat Sink, Remington 700
$6.00Heat sink for use in Remington 700 Bolt.
-
#1 Range Rod (Gordy Gritters/Grizzly)
$15.0022-6mm (243) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
Bolt Lug Lapping Tool – Remington 700
$15.00 -
Universal Bolt Welding Jig
$15.00Hold your bolt handle aligned properly to the bolt body while welding.
Product may differ from image.
Suggest ordering a heat sink at the same time to protect the threats and heat treat of your bolt during welding or brazing of the new bolt handle.
-
#2 Range Rod (Gordy Gritters/Grizzly)
$15.00257-7mm (280/284) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#3 Range Rod (Gordy Gritters/Grizzly)
$15.0030 caliber and up. Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
Remington 700 Receiver Tap
$24.00Receiver Tap for Remington 700 actions.
SPECS: 1 1/16″x16 tpi
-
.705″ CounterBore, Remington 700 and similar #3
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 30-49.
Specify pilot.
-
.705″ CounterBore #1, Remington 700 and similar
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 22-243.
Specify pilot.
-
.705″ CounterBore, Remington 700 and similar #2
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 25-29.
Specify pilot.
-
.705″ CounterBore, Remington 700 and similar #4
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 50 & 62.
Specify pilot.
-
Williams Scope Mount Drilling Fixture
$28.00Easily Drill and Tap your action for scope mounts.
fits receivers from .630” to 1.440”
-
Manson Floating Reamer Holder
$30.001/2″ straight shank for use in all Lathes and Mills.
-
Micrometer Reamer Stop
$30.00Precision, repeat-ability, and ease of use: these are the benefits of P. O. Ackley Micrometer Reamer Stop. Now you can do production runs with your Chamber Reamer, without having to index each workpiece axially. You’ll be assured of consistent headspace, chamber after chamber!
To set up, insert your Chamber Reamer shank in the Reamer Holder and tighten the two set screws. Then insert the reamer holder into the Stop Cylinder assembly (micrometer threaded Stop Cylinder with .001″ Adjustment Nut, Lock Nut and optional Plug Nut). Make a rough cut in the chamber (leave about .025″ extra material). Now, with the reamer bottomed in the rough chamber, move the Stop Cylinder assembly into contact with the work piece and secure it to the Reamer Holder with three set screws.
You can now adjust the depth of the finish cut in increments of .001″, or even less. The Adjustment Nut is marked with 25 equidistant markings around the circumference, each of which corresponds to .001″ of axial adjustment. By backing off the Adjustment Nut and re-securing the Lock Nut, then repeating the cut, you can zero in on your specified headspace measurement. Adjustments of .0005″ can be made with confidence.
We recommend use with our floating reamer holders for best results, with this rental.
.437″ straight shank for use in all Lathes and Mills.
-
Remington 700 Wrench (internal)
$30.00Action wrench for Remington 700 actions. This is the type that slides into the rails of the action. If your action has never been off the barrel from the factory, it may be too tight for this style of wrench.
You turn it with the 7/8″ Closed end wrench included in the rental.
-
Pillar Drilling Jig by Score High Gunsmithing
$100.00This stock drilling jig is by far the best method for drilling a Remington 700 stock to accommodate our adjustable pillars or pillars made by any one. Each kit comes with a specially modified drill that will not split or damage the stock. The drill bushing bar is the same diameter as a Remington action and is rigidly attached to the stock. It is actually a superior method to drill a stock than a drill press or even a milling machine. We only stock the 5/8″ drill and bushings.
No more damaged finish trying to remove the factory trigger guard from a bedded stock. No more trying to clean epoxy and mold release from the rough surface of a factory trigger guard. Our bedding blocks leave the bedded surface of your stock looking as if it just came out of a precision mold. Because these Bedding Blocks are made extra tall you never have to worry about the factory trigger guard being slightly below the stock’s finished surface and what to do with the epoxy that runs over the top.
Instructions included in the rental.
Complete Kit for all Remington 700 Variations.
