General Tool (rentals)
Rent these tools that might be used on any gun.
Showing all 34 results
-
Xtra Pilots for Removable Pilot / Bushing Reamers
$2.00You may request extra pilots at $2 rental fee each. Set the quantity total that you need in the shopping cart.
You will need to state the exact diameters you desire in the comments area at check-out. We do not have every imaginable pilot diameter, so we will fill all orders that we can and refund for any pilots (bushings) we cannot provide [no promise that we have what you want]. (refunds occur when the order is closed out upon tool returns)
-
Die stock – 1.5″
$5.00for use with 1.5″ dies
-
Tap Wrench
$6.00for hand reaming or taps
-
Heat Sink, Winchester 70
$6.00Heat sink for use in Winchester 70 Bolt.
-
Heat Sink, Enfield P-14 or P-17
$6.00Heat sink for use in Enfield Bolt.
-
Heat Sink, Remington 700
$6.00Heat sink for use in Remington 700 Bolt.
-
Heat Sink, Springfield Bolt
$6.00Heat sink for use in Springfield 1903 or 03-A3 Bolt.
-
Heat Sink, Mauser 98
$6.00Heat sink for use in 98 Mauser Bolt.
-
Ruger, Security Six, MGW Revolver Wrench Insert
$8.00Security Six
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
T Handle Reamer Extension
$10.00Comes with an adapter for standard 3/8″ square drive. Adapter can be removed to expose thread if you are using PTG or other tools that have a threaded drive end.
-
1911 Sear and Hammer Fixture
$10.001911 Sear & Hammer Jig allows you to:
- Demonstrate how the trigger / hammer parts group works
- Visually check hammer and sear engagement
- Test parts before your install them into your frame
- See the parts clearly from the top and sides
- Get that trigger right the first time.
- Modify parts for trigger jobs without the hassles of putting the part in and out of the frame.
Jigs are made in the USA out of high grade aircraft aluminum and to the same tolerances of a mil spec frames.
HAMMER, SEAR, PINS, AND GRIP SAFETY ARE NOT INCLUDED IN THIS RENTAL.
ONLY THE JIG BLOCK IS AVAILABLE to Rent!
-
14 x 1 Left Hand (LH) Die (7.62 guide)
$14.00Left hand thread for metric Flash Hiders or Muzzle Brakes
Includes a thread alignment tool (TAT) 7.62 Russian. When using a TAT make sure the tool never touches the end of the barrel, only the pilot.
If the TAT is allowed to touch the muzzle it is likely the tools will be damaged or you will damage your new threads. -
14 x 1 Left Hand (LH) Die (5.45 guide)
$14.00Left hand thread for metric Flash Hiders or Muzzle Brakes
Includes a thread alignment tool (TAT) 5.45×39 Russian. When using a TAT make sure the tool never touches the end of the barrel, only the pilot.
If the TAT is allowed to touch the muzzle it is likely the tools will be damaged or you will damage your new threads. -
#1 Range Rod (Gordy Gritters/Grizzly)
$15.0022-6mm (243) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
Universal Bolt Welding Jig
$15.00Hold your bolt handle aligned properly to the bolt body while welding.
Product may differ from image.
Suggest ordering a heat sink at the same time to protect the threats and heat treat of your bolt during welding or brazing of the new bolt handle.
-
#2 Range Rod (Gordy Gritters/Grizzly)
$15.00257-7mm (280/284) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#3 Range Rod (Gordy Gritters/Grizzly)
$15.0030 caliber and up. Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
Action Block & Lower Vise Block Set (AR-15)
$15.00Protect Receiver From Damage When Clamping
Heavy-duty blocks allow you to firmly clamp AR-15/M16 receiver halves in a vise without risk of crushing, twisting, or otherwise distorting them when applying vise pressure or torquing the barrel nut. Keeps your rifle secure for safe, effective cleaning, assembly, and repair. High pressure, solvent resistant, structural Rynite block and insert surround the entire upper receiver and support it inside and out to make rebarreling the AR-15/M16 an easy, one-man job. Lets you firmly secure a mil-spec carry handle receiver or mil-spec flattop receiver in a large bench vise for barrel removal/installation. Torque generated while tightening the barrel nut is transmitted to the block and insert, not the receiver. Minimizes the possibility of damage to the barrel detent pin and receiver detent notch. Holds securely without marring the finish.
DO NOT USE ON BILLET UPPERS OR LEFT HAND UPPERS, OR DAMAGE TO THE UPPER CAN RESULT.
-
1911 Plunger Tube Staking Tool (Brownells tm)
$20.00Easy-to-use rental tool lets you secure the plunger tube to your frame without fear of tube crush or expensive frame damage.
Adjustable to fit all makes of frames and tubes for both installing and re-tightening. Hardened crimping point. Plunger Tube Support slips inside plunger tube and prevents compression damage while tube is being staked to frame. Steel construction provides a rigid structure. (rental)
-
25-20 Barrel Liner Drill
$30.00Pilot length: 1″ (2.5cm). Pilot diameter: .25-20 – .247″ (6.8mm).
Same Drill that Brownells offers.
-
38-40 Barrel Liner Drill
$30.00Pilot length: 1″ (2.5cm). .38-40 – .391″ (9.9mm).
Same Drill that Brownells offers.
-
44-40 Barrel Liner Drill
$30.00Pilot length: 1″ (2.5cm)., .44-40 – .419″ (10.6mm).
Same Drill that Brownells offers.
-
Bolt Fixture, LaBounty
$36.00Simple and rigid lathe fixture that holds most common rifle bolts in a four-jaw chuck for face and locking-lug truing (both front and rear surfaces) or opening up the face to accept magnum cartridges.
-
12 Gauge, 55 degree Headspace Reamer (includes headspace ring)
$46.00 -
Pillar Drilling Jig by Score High Gunsmithing
$100.00This stock drilling jig is by far the best method for drilling a Remington 700 stock to accommodate our adjustable pillars or pillars made by any one. Each kit comes with a specially modified drill that will not split or damage the stock. The drill bushing bar is the same diameter as a Remington action and is rigidly attached to the stock. It is actually a superior method to drill a stock than a drill press or even a milling machine. We only stock the 5/8″ drill and bushings.
No more damaged finish trying to remove the factory trigger guard from a bedded stock. No more trying to clean epoxy and mold release from the rough surface of a factory trigger guard. Our bedding blocks leave the bedded surface of your stock looking as if it just came out of a precision mold. Because these Bedding Blocks are made extra tall you never have to worry about the factory trigger guard being slightly below the stock’s finished surface and what to do with the epoxy that runs over the top.
Instructions included in the rental.